Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - corb

Pages: [1] 2 3
Release Info / Qmod 22.2 released
« on: March 12, 2022, 02:19:12 pm »
This is a bug fix release
- Fixed: Sometimes wrong ratio calculation.
- Fixed: Leveler was sometimes a bit to agressive in band 4-5 when sudden level peaks occurred.
- Fixed: Gain calculation of the mp3 decoder was sometimes wrong.

Release Info / Qmod 22.1 released
« on: March 04, 2022, 08:24:59 pm »
Release info

- Added: Backup player now can play WAVE, FLAC, TTA and MP3 files in 2 channel 16bit stereo, with a samplerate of 44100 or 48000kHz (FLAC and TTA files are lossless open source codecs.)
- Changed: Moved the format list to a separate folder. So when you run two Qmod session on the same PC it doesn't conflict.
- Fixed: When no format was made and one format folder entry was empty, the backup player wouldn't play.
- Fixed: With the addition of FLAC, TTA and MP3 files some time problems with the backup player came up and are fixed now.

Release Info / Qmod 21.3 released
« on: October 24, 2021, 09:42:40 am »
Release info
- Added: An updated portaudio.dll.
- Added: Selectable audio folder. You'll find it on the setup tap of the silence panel.
- Changed: Minor backup player improvements.
- Changed: Minor leveler attack and release improvements.
- Fixed: A bug in the restart process of the device setup.
- Fixed: Some calculation errors in the fm processing and the composite clipper.

Release Info / Qmod 21.2 released
« on: June 16, 2021, 02:45:37 pm »
===== 21.2 ====
- Fixed: GUI error in formatplanner window. Formats at the bottom of the control coundn't be edit.
- Fixed: Added an extra channel to the backup player. In some cases the player could hang when a very short jingle was played.
  Origanaly the player had two playback channels which afterwards was not enough. Now there are three but in the qmod.ini you change this with the line: nrofchan=:=.
- Changed: Improvements on the compressor adaptive release control.

Release Info / Qmod 21.1 released
« on: May 25, 2021, 10:25:18 am »
What has changed?

- New: Added a control to set the player output.
- Changed: Some improvements on the processing core
- Changed: Some changes in the fm part to have a better bandwidth control. If you're using the fm part please check your output signal.
- Changed: When in FM or AM mode the line peak control is forced on, It gives some extra delay but better peak control.
- Changed: Improved the composite clipper.
- Fixed: Update check didn't work.
- Fixed: Some problems that stayed behind after the 20.4 release.
- Fixed: Problem in the leveler lock.
- Removal of old and disabled code.

Release Info / Wrong version of Qmod 20.4 was released. New one available
« on: November 06, 2020, 11:03:34 am »
For about an hour a wrong version of Qmod has been on-line.
Please download the update 20.4.1. Sorry for the mishap.

Release Info / Qmod 20.4 released
« on: November 06, 2020, 10:00:07 am »
===== 20.4 ====
- New: Show the playlist in the main window when the backup player is running. Does need special formatting of the track name. See the manual for more info.
- Changed: The way restart process operates so that it doesn't kill the backup player when changing the device setup.
- Changed: It's now possible to add more alternative frequencies when using RDS.
- Fixed: A few bugs in de GUI part that were introduced in 20.3 that caused a crash.
- Fixed: A few bugs in the backup player.

Release Info / Qmod 20.3 released
« on: September 21, 2020, 04:12:49 pm »
Release notes:

- New: Bass clipper added to the output limiter chain. Selectable are three options: off, soft and hard.
- New: Added a simple format planner to the backup player. Music as well as jingles can be ordered in a format. Read the manual for setup and use.
- Configuration GUI changes.
- An updated manual.
- Update of the default presets.
- Fixed: In the GUI/ The mix parameter was not updated when the preset was changed.
- Fixed: When you changed "the minimum tracks before repeat" in the backup player, Qmod would crash.
- Fixed: Expander part of the leveler didn't time correctly.
- Fixed: Bug in the API selection.

Release Info / Qmod 20.2 released
« on: July 09, 2020, 11:55:13 am »
Release note 20.2
- New: Auto release on the levelers, compressors and end limiter. When the release time is set to 0 the auto release is on.
- Some problems with the soundcard selection so I did a rewrite of the soundcard selection and detection of the device parameters. Thanks to ParelduikerFm for pointing it out.
- Rewrite of the fm peak control.
- Rewite of the end limiter. It's now a two band limiter.
- Added a buffersize of 3072 and 4096 samples to buffersize selection.
- Fixed the password showing in plain text on the silence panel.
- Fixed a bug in the ratio calculation that could crash Qmod.
- Fixed a bug in loading the config setup for a new install.
- Fixed a bug in the backup player. After input was restored the backup player didn't stop.
- Changed the logging. The newest entries are displayed first now.
- GUI changes. It's now possible to show level meters from the top down or bottom up, the setting for it is on the device panel and the leveler part is now on a separate panel. More changes in the next release.
- Some GUI fixes.

Release Info / Qmod 20.1 released
« on: May 01, 2020, 02:06:51 pm »
===== Release info ====
- New: Silence detector and backup player. When there's a loss of input signal the silence detector will start a backup player and can send an email.
  It includes a samplerate convertor. So when using a samplerate of 192000 and the backup player starts playing a WAV file with a samplerate of 44100kHz it's going to take more processing power.
  On my system its ~20%.
- Addressed some internal timing problems. The changes effect the leveler release setting  below 4s. You might want to check settings.
- Added a new portaudio dll that includes fixes.
- There's no longer a console version. The dll doesn't give audio card information anymore. If a crash happens, the error is saved in the Errorlog subdirectory.
- Some minor changes on the fm section. Still not completely satisfied but it will do for now.
- Fixed some bugs.

Release Info / Qmod 19.2 released
« on: December 30, 2019, 11:01:59 am »
Release notes

===== 19.2 ====
- Added: More test tone frequencies in the fm section.
- Added: A third option to the fm output. st line does the fm preprocessing but does deemphasize the signal afterwards and doesn't add 19kHz and RDS. You can use
  the signal for an external stereo encoder.
- Changed: Improvements in fm, am and line peak control sections.
- Changed: Improvement in the treble section.
- Changed: After a suggestion from Sevenmizer61, excluded the 19kHz and RDS component from the composite peak control.
- Fixid: Several bugs.

Release Info / Qmod 19.1 released
« on: August 01, 2019, 09:15:19 am »
===== 19.1 ====
From now on all support for Windows XP is no longer garanteed.
Version 18.6-32bit still had Windows XP support but to keep up with the Go language development I've decided to drop the Windows XP support.
Qmod could be working fine on XP but I've no way to test it.

- New: New resizable main window.
- New: A separate tab for pre-processing with now stereo+, low+ and treble controls
- New: Extra crash report. When a crash happens a file named qmodstackerror.txt appears in the Errorlog folder in the executable directory.
- New: A release hold setting. Values are 100ms - 2s with a step of 50ms till 1sec and 100ms above 1sec.
- New: A symmetry max. setting. Values are 0 - 3dB with a step of 0.
- Changed: Replaced the fm peak control with a new version for better spectrum control.
- Fixed: Several bugs.

Release Info / Qmod 18.6 released
« on: December 03, 2018, 10:33:57 am »
Release Notes

===== 18.6 ====
- Changed the low+ section.
- Changed some default preset settings.
- Replaced the Density control with five separate band controls.
- Removed the visual panel. It wasn't very useful and took unnecessary processing time when in use.
- Fixed: A wrong mix value of band 1 which resulted in a -2dB lower output of band 1.
- Fixed: When the peakcontrol was enabled it gave a glitch.
- Fixed: A few GUI bugs.
- Fixed: A timing bug in the leveler release and a bug in the core.

Qmod info / Qmod on Linux or Mac
« on: October 26, 2018, 02:07:21 pm »
You can run Qmod also on Linux or Mac by using Wine.

I've tested Qmod 18.5 x64 on Linux Mint 19 (Ubuntu 18.04) and Wine 3.03 stable. I have no Mac available so testing isn't possible by me. Feel free to test it yourself. You'll find more info on:

Release Info / Qmod 18.5 released
« on: September 22, 2018, 10:27:18 am »
Release info

- Added: Buffer size up to 2048 samples.
- Added: A preset planner. Gives you the possibility to automatically set a preset for every hour or a range of hours.
- Added: Selection of the equalizer setup, pre or post processing
- Fixed: A wrong buffer could occur in some cases.
- Fixed: A misreading of the proper samplerate return value after reinitializing the audio card.
- Fixed: Solved a bug in the peak control which caused some harmonic distortion.
- Fixed: Some bugs in the preset selection.
- Fixed: A bug in the noise reduction.

Pages: [1] 2 3